Homie Doesn't Want To Get His Lean On Anymore
I just put a McGaughy's 2/4 drop kit on my four-wheel-drive 2004 Chevy Silverado 1500. I've changed it a little. The truck comes from the factory with 2-inch lift blocks in between the axle and the leaf spring. I took those out and I have adjusted the torsion keys completely out so my 2/4 drop has become a 4/6 drop. Anyway, I'm having a problem with the right side of the truck leaning farther down. It's done this since I've owned it and I thought it might be shocks so I replaced those today. That didn't fix the problem. I'm just wondering if anyone has dealt with this before and might know what the hell is wrong.
Z71SS
via sporttruck.com

The problem with the truck sounds like the dreaded GM lean. From the factory, GM trucks don't sit level (I have seen as much as 5/8-inch difference from side to side). Changing the shocks won't help either. All you can do is adjust the torsion bars accordingly to help compensate for the factory lean. There is an even bigger problem with this truck, though. We strongly recommend that you do NOT lower a 1/2-ton four-wheel-drive any more than 2 inches in the front. This will cause an excessive CV joint angle which can cause vibrations, premature wear, and/or breakage. Please take our warning seriously because we have done a lot of testing and have seen these things happen. Thanks for your question!
Mike McGaughy
www.mcgaughys.com

McGaughy's has been in business over 25 years, engineering and manufacturing the world's finest lowering suspension parts. The company offers parts for 1960 to 2009 GM trucks and many other applications including Ford, Dodge, Nissan, and Toyota

We're Average, But In A Good Way
I am looking for a magazine for the everyday person who wants to work on his/her truck. Almost all of the magazines I look at are about nothing but lowering a truck and making it unrecognizable. If anything, I would like to raise my '94 S-10 a little. Does your magazine offer articles for the average truck enthusiast?Thank you,
Shawn
via email

We are far from average here at ST. But, we are a family of knuckle-busting gearheads that prides itself on getting' dirty in the driveway and turning wrenches whenever possible. To that end, you'll find lots of do-it-yourself tech articles in the magazine and on sporttruck.com. While the lifted truck scene has receded a bit as of late, you'll still see some tech articles on lifting sport trucks from time-to-time. You can also check out back issues of ST that feature tips on lifting the same kind of truck you have. In fact, check out the tech article section on sporttruck.com for a story where we lifted and lowered an S-10. Now, how is that for average?
Mike Finnegan / Editor

Depresssing Situation
I have an '00 Silverado on 'bags. When parked overnight or for a long period of time, the tail end loses air and eventually hits the ground. My compressor isn't kicking on either. If you can help with this I'd appreciate it. Thanks.
Rubbersidedown
via sporttruck.com

Most air systems are wired so that when the air in the reserve tank falls below a certain pressure, the pressure switch signals the relay to turn on the compressor and refill the tank. If the relay is powered by a wire that only provides voltage when the ignition is on, then it won't work when the truck is parked and not running. If you check out the schematic on this page, you'll see that in order for the pressure switch to have power, the ignition must be powered up. Without the ignition sending 12 volts to the pressure switch, the switch does nothing even if the air tank is empty.

Another issue to consider is that just because the rear 'bags are losing air doesn't mean that the reserve tank is losing air. If the tank is full, then there's no reason for the compressor to kick on. Even if it did, it's not going to automatically raise up the back of your truck unless you have the system plumbed and wired to do so. We suggest filling a squirt bottle with a soapy water solution (dish soap and tap water works well), fill up the 'bags with air, and then crawl under the truck and spray all of the air lines and fittings until you see bubbles. The bubbles indicate an air leak.
Mike Finnegan / Editor